Pool Table Lighting: Fixture Size, Height, and Bulbs
How to light a pool table: fixture length for 7, 8 and 9 ft tables, how high to hang it, how much light you need, and which bulbs show the balls true.
A pool table light has one job: even light across the whole bed and rails, with no glare in the players’ eyes and nothing for a cue to hit. Three numbers decide whether it does that job: the fixture’s length, its height above the table, and how much light reaches the cloth.
How high should a light hang above a pool table?
Hang the bottom of the fixture 30 to 36 in above the playing surface for typical home play. That is the range billiard retailers quote, and it keeps the light low enough to stay out of seated guests’ eyes while lighting the corners.
The World Pool-Billiard Association sets a higher bar for tournaments: a fixture that can be moved aside must sit at least 40 in above the bed, and a fixed fixture at least 65 in. The reason is the cue. On jump and masse shots the butt of the cue rises steeply, and a fixture at 30 in can be in the way. If anyone in your house jumps balls or practises masse, hang the light at 36 to 40 in and buy a brighter fixture to make up for the extra height.
| Standard | Fixture bottom above the bed | Above the floor (bed at about 31 in) |
|---|---|---|
| Home convention, low | 30 in | about 61 in |
| Home convention, high | 36 in | about 67 in |
| WPA, movable fixture | 40 in minimum | about 71 in |
| WPA, fixed fixture | 65 in minimum | about 96 in |
How long should a pool table light be?
Choose a fixture about 65 to 85 percent as long as the playing surface. Diamond Billiards’ tournament LED panels fall in that range: 60 in long for 7-foot tables and 84 in for 9-foot tables, listed on diamondbilliards.com in October 2026.
| Table (playing surface) | Fixture length (our range) | Diamond tournament panel |
|---|---|---|
| 7 ft (78 x 39 in) | 51 to 66 in | 60 x 24 in, two panels |
| 8 ft home (88 x 44 in) | 57 to 75 in | none listed |
| 9 ft (100 x 50 in) | 65 to 85 in | 84 x 24 in, three panels |
A fixture that is too short leaves the corner pockets and rails dim. One that is too long, or as long as the table, puts the shade ends above the players’ heads as they lean in at the corners. Table playing surfaces vary by maker, so check yours in the pool table sizes guide before ordering.
How much light does a pool table need?
The WPA requires at least 520 lux, which is 48 footcandles, at every point of the bed and rails, with the center not noticeably brighter than the corners. That works out to a minimum amount of light landing on the table:
| Table (outside size) | Area | Light landing on the table at 520 lux |
|---|---|---|
| 7 ft (86.6 x 48.6 in) | 2.72 m² | about 1,400 lumens |
| 8 ft (98.5 x 54.5 in) | 3.46 m² | about 1,800 lumens |
| 9 ft (110.5 x 60.5 in) | 4.31 m² | about 2,250 lumens |
A fixture’s rated lumens are not the lumens that land on the cloth; part of the output spills past the rails and the shades absorb some. That is why real fixtures are rated well above these figures. Diamond’s 7-foot tournament panel is rated at 8,800 lumens and its 9-foot panel at 13,200 lumens. A cheap three-shade light with one small bulb per shade can fall short of 520 lux at the corners even when the center looks bright. The outside sizes above are Brunswick’s Allenton 7, Glenwood 8 and Glenwood 9.
Which bulbs and color temperature work best?
Use LED bulbs or an integrated LED fixture in neutral white, about 4000 to 5000 K, with a color rendering index (CRI) of 90 or higher. That is our recommendation, and the reason is in the balls themselves.
Under the WPA ball spec, the 3 is red, the 5 orange and the 7 maroon, and the striped 11, 13 and 15 repeat those colors on white. Very warm light around 2700 K pushes all three toward the same reddish brown, and low-CRI bulbs flatten them further. Neutral, high-CRI light keeps them distinct from across the table. LEDs also run cool, which matters with a fixture 30 in above a player’s head, and a dimmer on the circuit lets the same light work for games and for a quiet evening.
How do you avoid glare and shadows?
Shade or diffuse every light source so no bare bulb is visible from a standing player’s eye level at the rail. The WPA calls for a screen or reflector setup so the center of the table gets no more light than the rails and corners, and it notes that blinding light starts at 5,000 lux in direct view.
Shadows come from too few sources. A single pendant over the middle lights the center well and leaves the rails and corner pockets dim. Multi-shade bar fixtures and long LED panels spread the light along the table’s length, which is why both the home and tournament worlds use them. Matte shades and diffusers beat glossy ones: a shiny shade reflects into the eyes of whoever is bending over the far rail.
How does ceiling height change the setup?
On an 8 ft (96 in) ceiling, the fixture bottom sits 29 to 35 in below the ceiling in the 30 to 36 in home range, so the chain or rod plus the fixture body must fill that gap. On a 7 ft (84 in) ceiling, the gap shrinks to 17 to 23 in, still enough for a low-profile LED panel.
The WPA’s 65 in rule for fixed fixtures puts the light about 96 in off the floor, which is the ceiling itself in most homes. In practice, fixed home fixtures hang lower and the 40 in movable-fixture rule is the useful tournament reference. Very low ceilings are a bigger problem for the cue than for the light: if a jacked-up cue butt touches the ceiling, no fixture choice helps. Run your room through the game room planner with the ceiling height entered and it will check whether a light can hang at the height you want.
Can you install a pool table light yourself?
A plug-in fixture hung from ceiling hooks is a DIY job if you follow the manufacturer’s manual for the hooks, the chain and the load rating. Anything hardwired is different. Connecting a fixture to an existing ceiling box should follow the fixture manual and your local electrical code, and a new box or a new circuit is work for a licensed electrician.
Two practical checks before ordering. First, find the ceiling joists over the table’s center: a 26 to 55 lb panel (Diamond’s 7-foot tournament and Professional panels are listed at 26 and 55 lb) needs solid fixing, not drywall anchors. Second, check where the switch will be; a switch by the door beats reaching under the fixture. Lighting is one of the line items to add to a table budget, along with delivery and accessories, in our pool table cost guide.
Who a full tournament-style fixture is not for: a 7-foot table in a family room where the light also has to look good from the sofa. A three-shade fixture at the right length and height, with neutral high-CRI LED bulbs, will meet the brightness target for casual play. Our pool table buying guide covers the rest of the setup.
Where do these numbers come from?
- 520 lux at every point, screens and reflectors, 40 in and 65 in fixture heights, the 5,000 lux glare threshold, bed height and ball colors: World Pool-Billiard Association, Recommended Equipment Specifications, section 15 and related sections (wpapool.com), read October 2026.
- Fixture lengths, lumens and weights: diamondbilliards.com lighting listings, read October 2026.
- Table outside dimensions used for the area math: brunswickbilliards.com product pages, read October 2026.
- The 30 to 36 in home range: billiard retailer guidance. Lumens-per-table, fixture-length ranges and ceiling gaps are our calculations; the color temperature and CRI advice is our recommendation.
Frequently asked questions
Quick answers to what readers ask us most
How high should a light be above a pool table?
Most home installs put the bottom of the fixture 30 to 36 in above the playing surface. The WPA tournament rule is at least 40 in for a fixture that can be moved aside and 65 in for a fixed one.
How long should a pool table light be?
About 65 to 85 percent of the playing surface length: roughly 51 to 66 in for a 7-foot table, 57 to 75 in for a home 8-foot and 65 to 85 in for a 9-foot. Diamond's tournament LED panels are 60 in for 7-foot and 84 in for 9-foot tables.
How bright should a pool table light be?
The WPA requires at least 520 lux (48 footcandles) at every point of the bed and rails, without the center being noticeably brighter than the corners. Blinding light starts at 5,000 lux in direct view.
What color temperature is best for a pool table light?
Neutral white, about 4000 to 5000 K, with a color rendering index of 90 or higher. Very warm light makes the red 3, orange 5 and maroon 7 balls harder to tell apart.
Can I install a pool table light myself?
A plug-in fixture hung from ceiling hooks is a DIY job if you follow the manual. A hardwired fixture or a new ceiling box or circuit should follow the fixture manual and local electrical code, and new circuits are work for a licensed electrician.