Slate vs Non-Slate Pool Tables: What You Give Up
Slate or non-slate pool table? Flatness, weight, price and moving compared with WPA specs and same-model price pairs, plus when non-slate is the smarter buy.
Slate or not is the biggest single decision in a pool table, and it is the one that changes price, weight and how the table plays ten years from now. This page compares the two honestly, including the cases where the cheaper table is the right buy.
What is the difference between slate and non-slate pool tables?
A slate pool table has a playbed made of quarried slate stone, usually 1 in thick and in three pieces, covered in cloth. A non-slate table uses a manufactured board instead, typically MDF or laminated engineered wood, sometimes sold under a brand name. Everything else, from rails to pockets, can look the same, which is why the bed is the first thing to ask about.
| Slate | Non-slate | |
|---|---|---|
| Bed material | Natural slate stone | MDF or engineered wood |
| Typical thickness | 1 in (3/4 in on small tables) | Varies by maker; 18 mm on American Legend tables |
| Flatness over time | Stays flat; can be re-leveled at the seams | Can sag or swell over the years |
| Weight (8 ft) | About 950 lb shipping weight (Imperial Eliminator) | A fraction of that |
| Price, same model | $400 to $700 more (Mizerak pairs, Oct 2026) | Lower |
| Setup | Professional install, $399 to $899 at major brands | Usually self-assembly |
| Moving | Must be taken apart; pros average $650 | Two people can often move it whole |
| Resale | Holds value if the slate is intact | Little resale value |
What does the official standard say a slate bed must do?
The World Pool-Billiard Association (WPA) sets the equipment standard for tournament tables, and its numbers show why slate matters. The WPA specification requires:
- Slate at least 1 in (2.54 cm) thick.
- Flatness within 0.020 in lengthwise and 0.010 in across the width.
- No more than 0.030 in extra deflection under a 200 lb load at the center.
- Slate seams level with each other within 0.005 in after shimming.
- For tournament tables, three pieces of equal size with a wooden frame at least 3/4 in thick attached underneath.
The WPA notes that its specifications do not necessarily apply to tables made for home use. Still, those tolerances are the reason slate is the reference material: a stone bed can be shimmed and leveled to a few thousandths of an inch and stay there.
What are non-slate beds made of?
Usually MDF (medium-density fibreboard) or a laminated engineered-wood panel. A few examples from listings checked in October 2026:
- American Legend Kirkwood and Brookdale: an 18 mm, two-ply laminated engineered-wood playfield, which the maker says resists warping.
- Mizerak Dynasty Space Saver: a double-sealed MDF playbed.
- Minnesota Fats Covington: a “Dur-A-Bond” playbed, designed to install in under an hour.
- Mizerak Slatron tables: sold side by side with slate versions of the same model. Escalade’s listings do not describe what Slatron is made of.
Brand names like these are not slate. If a listing does not say “slate” and give a thickness, ask what the bed is made of before you buy.
How much more does slate cost on the same table?
$400 to $700 on the same model, before installation. Escalade sells two Mizerak 8 ft tables in both versions, which removes the usual noise of comparing different cabinets:
| Model (Escalade Sports, Oct 2026) | Non-slate (Slatron) | Slate | Difference |
|---|---|---|---|
| Mizerak Dakota 8 ft | $1,899.99 | $2,599.99 | $700 |
| Mizerak Donovan II 8 ft | $1,999.99 | $2,399.99 | $400 |
Then add setup. Brunswick includes delivery and installation by an authorized installer in an $899 fee; Imperial charges $399 for required professional installation. The pool table cost guide has the full price bands and a first-year total.
Does a slate pool table damage floors?
Rarely, on a normal house floor. The weight sounds alarming, but it is spread out. The Imperial Eliminator 8 ft is 102 x 58 in overall, about 41 sq ft, with an approximate shipping weight of 950 lb. That works out to about 23 lb per sq ft.
US residential code (IRC Table R301.5) designs floors in living areas for a live load of 40 lb per sq ft, so a slate table on a typical framed floor or basement slab is within that. The load does reach the floor through the legs, so on an old house, a long-span upper floor or anything that already bounces, ask a contractor or structural engineer before delivery. Protect finished floors with leg cups or pads.
One-piece or three-piece slate?
Three-piece slate is the norm for home tables, and it is what the WPA requires for tournament tables. Three pieces are easier to carry and let an installer level each piece and close the seams with shims and filler. One-piece slate has no seams but is very heavy to move and hard to level if the floor is not flat.
Thinner slate shows up on small tables. Berner’s Basic Slate bumper pool table uses a 3/4 in slate bed, which is normal at that size. See the bumper pool table guide. On a full-size 8 ft table, ask why if the slate is thinner than 1 in.
How heavy is the slate itself? Slate has a specific gravity of about 2.8, so a 1 in bed the size of a home 8 ft playing surface (88 x 44 in) weighs about 390 lb before counting the slate under the rails. In a three-piece set that is at least 130 lb per piece. That is why slate tables are taken apart to move, which the pool table moving guide covers step by step.
Does humidity matter more for one type?
Yes. Wood-based beds absorb moisture, and MDF can swell or lose flatness in a damp basement or an unheated garage. Slate does not absorb moisture the same way, though the wood frame, rails and cloth on a slate table still react to damp air. If the room swings between humid summers and dry winters, slate is the safer bed, and a dehumidifier helps either way.
When is a non-slate table the right call?
When the table is temporary, light use, or has to move. Non-slate is a sound buy in these cases:
- Young kids who will mostly bank balls around. You can upgrade when they get serious.
- Renters or anyone likely to move within two years. A pro slate move averages about $650 each time.
- Upper floors and tight stairs, where a 950 lb delivery is impractical.
- A budget under about $1,500. A well-built non-slate table beats a bargain slate table with a weak frame and no installer.
- Conversion tables. Pool tables with ping pong or dining tops are mostly non-slate, for example the Triumph Phoenix 7 ft with a table tennis top at $949.99 (Escalade Sports, Oct 2026).
When is slate worth the extra money?
When the table will stay put and someone in the house wants to get better at pool. Slate also makes sense when you expect to sell the table one day, because used slate tables keep a market while used MDF tables mostly do not. If you are buying slate, put the money into the installer: a level, well-joined bed matters more than a carved leg.
Which size and room do you need either way?
The bed material does not change the room. An 8 ft home table with standard 58 in cues needs about 13 ft 4 in x 17 ft 0 in whether it is slate or not. Run your room through the room planner and read the pool table buying guide for cushions, cloth and frame quality.
Where do these numbers come from?
- WPA Recommended Equipment Specifications, sections 4 (slates) and 1 (purpose).
- Mizerak, American Legend, Minnesota Fats and Triumph listings at Escalade Sports, checked October 6, 2026.
- Imperial Eliminator 8 ft specs, weight and installation fee.
- Brunswick Santini 8 ft delivery and installation terms.
- HomeAdvisor, pool table moving cost, updated June 20, 2026.
- Berner Basic Slate bumper pool table at GameRoomShop.
- International Residential Code Table R301.5 (minimum uniformly distributed live loads).
Frequently asked questions
Quick answers to what readers ask us most
Is a slate pool table worth it?
For a table that will stay in one room for years, yes. Slate stays flat, can be leveled precisely and keeps resale value. On the same Mizerak models, slate cost $400 to $700 more than non-slate in October 2026, plus installation.
How thick should pool table slate be?
1 in is the standard for home and tournament tables, and the WPA requires at least 1 in for sanctioned play. Some small tables use 3/4 in slate, and some premium tables use 30 mm. Very thin slate on a full-size table is a red flag.
How heavy is a slate pool table?
An 8 ft table with 1 in three-piece slate is heavy: Imperial lists an approximate shipping weight of 950 lb for its 8 ft Eliminator. Non-slate tables weigh a fraction of that and two people can usually move them.
Can a non-slate pool table be leveled?
Only at the legs. Most non-slate tables have leg levelers or shims, which fix a sloped floor but not a playbed that has sagged or warped. Slate tables can also be shimmed under each slate piece and at the seams.
Will a slate pool table damage my floor?
Usually not on a normal house floor. An 8 ft slate table spreads about 950 lb over roughly 41 sq ft, about 23 lb per sq ft, below the 40 lb per sq ft that US code designs living-area floors to carry. Ask a pro about old or unusual floors.