GameRoomWise Game room tables, sized and chosen with real numbers
Pool Tables

How to Move a Pool Table Without Wrecking the Slate

How to move a pool table: what it weighs, why slate tables come apart, the step order, what pro movers charge in 2026, and when not to do it yourself.

How to Move a Pool Table Without Wrecking the Slate
The short answer A slate pool table weighs about 600 to 1,200 lb, so it is moved in pieces: pockets, rails, cloth, then the slate sections, carried on edge. Pro movers charged $375 to $1,500 in 2026, about $650 on average. The hard part is reassembly: the slate must be leveled and the seams filled flat before the cloth goes back on.

The reason pool tables are hard to move is not the weight alone. It is that a slate table is a precision surface held flat by its frame, and every piece you take off has to go back to within a few thousandths of an inch. This guide covers what a table weighs, how it comes apart, what movers charge, and when to leave it to them.

How much does a pool table weigh?

A slate pool table weighs about 600 to 1,200 lb assembled, depending on size and build. Non-slate tables with MDF or composite beds weigh a fraction of that and can often be moved in one piece.

TableSizeWeight (as listed)
Brunswick Allenton7 ft598 lb unpackaged, 686 lb packaged
Diamond Professional / Pro-Am / Smart7 ft800 lb
Imperial Eliminator8 ftabout 950 lb (approximate shipping weight)
Diamond Professional / Pro-Am / Smart8 ft1,000 lb
Diamond Professional / Pro-Am / Smart9 ft1,200 lb
HomeAdvisor typical, one-piece slatevariousabout 450 lb
HomeAdvisor typical, three-piece slatevarious600 to 650 lb

The slate is most of it. A 1-inch bed the size of the playing surface alone weighs about 390 lb on a home 8-foot table (88 x 44 in) and 505 lb on a 9-foot (100 x 50 in), at slate’s specific gravity of about 2.8. Split into three sections, that is at least 130 to 170 lb per piece before the wooden backing and the slate under the rails. Sizes are covered in pool table sizes and dimensions.

Why do slate pool tables have to be taken apart?

Because the slate is fixed, leveled and sealed as one surface. The WPA spec for tournament tables calls for three equal slate sections screwed to the frame, flat within 0.020 in along the length and 0.010 in across, with every seam in the same plane within 0.005 in after leveling and shimming.

Lifting an assembled table by its rails or dragging it flexes the frame under several hundred pounds of slate. That can crack the seam filler, shift the sections, loosen rail bolts or crack a slate corner. Even a perfect lift leaves a table that has to be re-leveled in its new spot. Taking it apart turns one 1,000 lb lift into several manageable ones, and the table has to be leveled again anyway. The difference between slate and non-slate beds, including how each behaves in a move, is in slate vs non-slate pool tables.

What are the steps to take a pool table apart?

Work from the top down and keep every fastener with the part it came from. The order below is the general one; follow your table’s manual where it differs.

  1. Pockets. Remove drop-pocket liners, usually stapled or screwed under the rails. Ball-return tables have a gully system to unbolt underneath.
  2. Rails. Undo the bolts under the rail edge from beneath the table and lift the rails off in sections. Label each rail and its position.
  3. Cloth. Pull the staples holding the bed cloth to the wooden backing under the slate, slowly if you want to reuse it. Glued cloth usually cannot be saved.
  4. Slate. Scrape the filler from the seams, remove the screws holding each section to the frame, and lift each section straight up.
  5. Frame and legs. Unbolt the legs and frame members if the frame will not fit through doors or stairs.

Bag the bolts, screws and shims by section. Shims are the part most often lost and the most expensive to rediscover, since they hold the level.

How do you transport the slate safely?

Carry and transport slate sections on edge, not flat, wrapped in moving blankets. On edge the stone resists bending; laid flat and carried by the ends, a section can flex and crack.

Use a furniture dolly or a carpeted dolly sized for the section, and plan the route before lifting: measure doorways, stair turns and ceiling clearance on stairs. Strap each section upright in the truck against a wall or a padded rack so it cannot tip. Rails go flat, padded, with nothing heavy stacked on top, because the cushion rubber and the sights are easy to damage. The new room needs checking too: use the game room planner to confirm the table and its cue clearance fit before moving day, not after.

How is a pool table reassembled and leveled?

Reassembly is the reverse order, with leveling as the critical step: frame first, leveled with a machinist’s level, then slate sections set, aligned, shimmed and screwed down. The seams are then filled, traditionally with beeswax, and scraped flat before any cloth goes on.

Check level along the length, across the width and on the diagonals, and re-check after the slate screws are tightened, since tightening can pull a section out of line. The WPA’s tournament tolerance of 0.005 in at the seams is a useful benchmark for how flat “flat” means. The cloth then goes on stretched evenly in both directions, followed by the rails (torqued evenly so the cushions play the same everywhere) and the pockets. A table that rolls off line after a move almost always has a leveling or seam problem, not a cloth problem.

How much do pool table movers charge?

HomeAdvisor’s cost data, updated June 20, 2026, puts the normal range at $375 to $1,500 and the average at $650. Long-distance moves can reach $4,000 or more.

Item (US, 2026)Typical price
Local move, disassembly and reassembly$375 to $1,500, average $650
Long-distance moveup to $4,000 or more
Disassembly and reassembly, if billed separately$75 to $200 extra
Re-felting during reassembly$250 to $450, about $300 average, cloth choice extra
Crew time4 to 6 hours for a standard move

For comparison, Brunswick charged a flat $899 shipping and handling fee in October 2026 to deliver and install a new table with an authorized installer. A move between two of your own rooms is cheaper than a cross-town move because the truck and the drive drop out, but the labor of taking down and leveling the table does not. Moving costs sit alongside purchase prices and cloth prices in our pool table cost guide.

When should you not move a pool table yourself?

Hire a billiard mover, or a mover who brings a billiard technician, if any of these apply:

  • Three-piece slate and no leveling experience. Taking the table apart is the easy half. Leveling slate to a few thousandths of an inch is the skill you are paying for.
  • Stairs or tight turns. Slate sections on a staircase are a crush and fall risk for the people below.
  • Fewer than three or four helpers. Each section can weigh well over 100 lb, and slate does not bend to fit a grip.
  • A warranty you want to keep. Read the warranty terms before you open the table.
  • Glued cloth or a cloth you love. You may be buying new cloth either way; a pro can tell you before the job starts.

DIY makes sense for non-slate tables, and for owners who have assembled their own slate table before and have the level, shims and helpers to do it again. For anyone else, the mover’s fee is small next to the cost of a cracked slate.

Where do these numbers come from?

  • Table weights: brunswickbilliards.com (Allenton 7 ft), imperialusa.com (Eliminator 8 ft) and diamondbilliards.com (Professional, Pro-Am, Smart) product pages, read October 2026.
  • Moving costs, typical weights, re-felting costs and crew time: HomeAdvisor, pool table moving cost, updated June 20, 2026, read October 2026.
  • New-table delivery fee: brunswickbilliards.com product pages, read October 2026.
  • Slate construction and flatness tolerances: World Pool-Billiard Association, Recommended Equipment Specifications (wpapool.com), read October 2026.
  • Slate weight: our calculation at 1 in thick and a specific gravity of 2.7 to 2.9 (Wikipedia, “Slate”).

Frequently asked questions

Quick answers to what readers ask us most

How much does a pool table weigh?

Slate tables weigh about 600 to 1,200 lb assembled. Brunswick lists its 7-foot Allenton at 598 lb, and Diamond lists its 7, 8 and 9 foot tables at 800, 1,000 and 1,200 lb. Non-slate tables weigh far less.

How much does it cost to move a pool table?

HomeAdvisor's June 2026 figures put the normal range at $375 to $1,500, with an average of $650. Long-distance moves can reach $4,000 or more, and re-felting adds about $250 to $450 plus the cloth.

Can you move a pool table without taking it apart?

A non-slate table, or a short move of a one-piece slate table by a full crew, sometimes. A three-piece slate table should be taken apart, because its slate sections are leveled and sealed in place and lifting the whole table can shift or crack them.

Can I reuse the cloth after moving a pool table?

Sometimes. Stapled cloth removed slowly can be reused, but it has already been stretched once and may not tension evenly again. Glued cloth usually tears. Many owners re-felt during the move: HomeAdvisor puts the service at $250 to $450, and premium cloth costs extra.

How many people does it take to move a pool table?

Plan on at least three or four strong adults for the slate sections, which can weigh well over 100 lb each, plus someone who knows the reassembly. Pro crews usually finish in four to six hours.